Matrix 2.8m TR PRO

Debido a su volumen este modelo tendrá unos gastos de envio de 60€ y será enviado por CBL (2 o 3dias)
Tambien estaria disponible la opcion de recogerlo en tienda, no tendria gastos de envio.

after great feedback with Matrix 2.2 we decided to develop Big Matrix for new era. this big Matrix is an innovative approach to a new sport jet/ 3Djet. Great capabilities had to be combined between sport jet and unbeatable 3D performance. everything aerodynamic we tested and learned from Matrix and develop together with one of the best pilot in the world more than 1 year test so this one is next level of Matrix performance so we can say this is best big sport jet we had done with ultimate flying characteristics for precise aerobatics and 3D aerobatics at the same time we upgrage design of wing develop base from 2.2 to 2.8 with new feature aileron with tip aileron counter balance aid in roll authority and allow for one aileron servos per wing and flaps can be work as aileron for full axial roll.
The Matrix all feature and shape of airframe this from one of the best designer Mirco Pecorari from Aircraftstudiodesign, a little like the charismatic hypercars style.

Specifications:

 FEATURES:

• Extremely lightweight full composite construction especially designed for outstanding sport flight with 3D performance
• Painted outside the mold so no seam lines
• Ultra light weight landing gear special build for Matrix 2.8m 
• Specially designed easy access to turbine for speedy installation
• Field setup can be done in seconds, thanks to the quick releases on the wings without the need for any tools.
•  the single elevator clamp from the top, only a few turns to tight/loose the bolt then you can install/take out the stabilizer. 
• flap can use as aileron to make very axial rolling performance with counter balance on tip aileron allow to use only 1 servo per aileron
• Removable wing and stabilizer and vertical fin for easy transport
• Removable two piece of fuselage for easy transport, only four bolt to lock two piece fuselage. tail pipe is fixed on the back section of fuselage. front fuselage is 1927mm, back fuselage is 875mm
• The equipment installation board make the electronic items with very clear installation. Most of the wire can be hidened. 
• pre-install tube for the stab/rudder extension wire, easy to install. 
• Option with vector tail pipe for 3D flight. 

 Hardware incluido

• Cables para alas y fuselage 4in1
• Cables 3in1 para las 2 piezas del fuselaje
• Cables 2in1 para las 2 piezas del fuselaje (option for vector version)
• Complete air frame (including carbon wing-tubes and preinstalled and painted fiberglass control horns)
• Tobera vectorial
• Deposito bolsa 5.500ml
• Deposito bolsa para humo 1800ml
• Pre-prepared pushrods con ball links
• Servo connector brackets
• TR PRO 2.8m Matrix jet con deposito de combustible de bolsa, deposito de humo de bolsa, bomba de humo, tobera vectorial tailpipe, tren retractil electrico con freno, servos y hardware, preinstalado en fabrica, tambien incluye bolsa para alas y funda de fuselage.

 Hardware requerido:

Turbine :

• 160-240N para vuelo normal sport
• 250-320N para vuelo 3D con vector – Avoid high speed high G flying

Servos: Total x10 ( standard size )
x2 for flaps (minimum 40kg)
x1 for rudder (minimum 40kg)
x2 for ailerons (minimum 40kg)
x2 for elevators (minimum 40kg)
x1 for vector elevator (minimum 37kg), this is option
x1 for vector rudder (minimum 37kg), this is option
x1 for steering (minimum 21kg)

Also requires all the usual accessories such as transmitter, receiver, batteries, powerbox and possibly other small accessories.

Control Throw in all surface

for Sport flight

Aileron: 44mm, Rudder: 50mm, Elevator: 16mm.
Flap: 74mm for take off and 108mm for landing.

for 3D flight

Aileron: 88mm up and 83mm down , Flap to Aileron is 114mm up and 108mm down Rudder: 70mm, Elevator: 20mm.

Center Of Gravity

Measured back from leading edge of the wing 335mm