Todas las categorías

.

Todas las categorías

.

Matrix 2.2m con tren sin vectorial

3.250,00 €
Impuestos incluidos
Cantidad:

Size Chart
x
Size Chart

Measuring Tips to Assure The Best Fit

  • Measure your back size – wrap the measuring tape snugly around your ribcage, just under your bust line 1, keeping it horizontal. This will give you your band size.
  • Then measure around the fullest part of your bust 2 , again keeping the tape horizontal.
  • To determine the size of pants, measure the girth of the waist 3 and hips 4
  • The following charts will help you match the designer’s size scheme for this product (indicated in the dropdown) to your usual size

size guide visible to all products

UKUSAEUBUSTWaistHips
XS 8 4 34 31/32 23/24 33/34
S 10 6 36 33/34 25/26 35/36
M 12 8 38 35/36 27/28 37/38
L 12 8 38 35/36 27/28 37/38
XL 10 6 36 33/34 25/26 35/36

Debido a su volumen este modelo tendrá unos gastos de envio de 60€ y será enviado por CBL (2 o 3dias)
Tambien estaria disponible la opcion de recogerlo en tienda, no tendria gastos de envio.

SPECIFICATIONS:

Model: Matrix 2.2
Wingspan: 78.7″ (2,000mm)
Length: 87.6″ (2,225mm)
Wing area: –
Weight: 21.9lbs (9.94kg)

FEATURES:

  • Extremely lightweight full composite construction especially designed for outstanding sport flight with 3D performance
  • Painted outside the mold so no seam lines
  • Ultra light weight landing gear,  the 2.2m predator sport jet V2 landing gear can use to the Matrix too. 
  • Specially designed easy access to turbine for speedy installation
  • Field setup can be done in seconds, thanks to the quick releases on the wings without the need for any tools.
  •  the single elevator clamp from the top, only a few turns to tight/loose the bolt then you can install/take out the stabilizer. 
  • Removable wing and elevator for easy transport
  • The equipment installation board make the electronic items with very clear installation. Most of the wire can be hidened. 
  • pre-install tube for the stab/rudder extension wire, easy to install. 
  • Option with vector tail pipe for 3D flight.

INCLUDED HARDWARE:

  • Complete air frame (including carbon wing-tubes and preinstalled and painted fiberglass control horns)
  • Pilot-RC electric retracts and electric brakes specific for this model
  • Servo extension leads
  • Normal tail pipe (optional Vector thrust pipe)
  • 3.800ml fuel tank (optional upgrade to fuel bag)
  • 250ml UAT tank
  • Pre-prepared pushrods with ball links
  • Servo connector brackets

REQUIRED HARDWARE:

Turbine size:

  • 100-140N for normal sport flying
  • 160-180N for 3D vector flight – Avoid high speed high G flying

Servos: Total x10 (x5 standard size + x5 medium size)

x3 standard size high torque
x2 for flaps (minimum 40kg)
x1 for rudder (minimum 40kg)

x7 medium size servo  (size: 35x15x30mm)
x2 for ailerons (minimum 16kg)
x2 for elevators (minimum 16kg)
x1 for vector elevator (minimum 16kg), this is option
x1 for vector rudder (minimum 16kg), this is option
x1 for steering (minimum 10kg)

Also requires all the usual accessories such as transmitter, receiver, batteries, powerbox and possibly other small accessories.

Decoraciones disponible para pedir

deco 02

Deco 03

Deco 04

matrix2.2-03

Referencias específicas

Productos Similares